Stroboscope

Lutron DT-2239A – Digital Stroboscope

Name: Lutron DT-2239A - Digital Stroboscope
Brand: Lutron
SKU: L-DT2239A
Availability: InStock

Availability:

Stok 1

Compare

The DT-2239A Digital Stroboscope provides accurate and reliable measurements of the speed of moving gears, fans, centrifuges, pumps, motors, and other equipment, making it an essential tool for industrial maintenance, production, quality control, and educational demonstrations.

Status Barang: Ready

Kondisi: Baru

Minimal Order: 1 pcs

Rp3.484.000,0

Stok 1

DIGITAL STROBOSCOPE
Model: DT-2239A

OVERVIEW:
The model DT-2239A is a microprocessor circuit design, high accuracy, digital readout, light duty STROBOSCOPE/TACHOMETER that is ideal for inspecting and measuring the speed of moving gears, fans, centrifuges, pumps, motors and other equipment used in general industrial maintenance, production, quality control, laboratories and as well as for schools and colleges for demonstrating strobe action.

FEATURES:
◆ Display: 0.3″ LED, 4 digits
◆ Stroboscopic: Flash Rate 100 to 10,000 flashes per minute (FPM)
◆ Accuracy:
100 to 5,000 FPM/RPM) – ± 1 digit
over 5000 FPM/RPM – ± 0.05%
◆ Resolution:
Less than 10,000 FPM/RPM – 1 FPM/RPM
Over 10,000 FPM/RPM – 10FPM/RPM
◆ Sampling Time: 1 second
◆ Range: Select Automation.
◆ Housing: Compact and impact plastic injection case with plastic mirror type reflector
◆ Calibration Crystal time base and microprocessor circuit, don’t necessary take any external calibration process
◆ Flash tube: Xenon lamp
◆ Flash Duration: Approximately 60 to 1,000 microseconds
◆ Flash color Xenon white 6,500 K degree
◆ Beam Angle: 80

EACH UNIT INCLUDES WITH:
◆ Operation manual

SKU: L-DT2239A Kategori: Stroboscope Brand: Lutron

Berat	2 kg

SPECIFICATIONS
Display	0.3″ LED, 4 digits.	Power Supply	110 Vac 10%, 50/60 Hz.
Stroboscopic Flash Rate	100 to 10,000 flashes per minute (FPM).		or 220 Vac 10%, 50/60 Hz.
			or 230 Vac 10%, 50/60 Hz.
Accuracy	100 to 5,000 FPM/RPM) – ± 1 digit.	Power Consumption	Less than 30 Watt.
	over 5000 FPM/RPM – ± 0.05% .	Operating Temp.	0 to 50 °C (32 to 122 °F).
		Operating Humidity	Less than 80% R.H.
Resolution	Less than 10,000 FPM/RPM- 1 FPM/RPM.
		Dimension	HWD – 21 x 12 x 12 cm (8.3×4.8×4.8 inch).
	Over 10,000 FPM/RPM – 10FPM/RPM
		Weight	1Kg/2.2 LB.
Sampling Time	1 second.	Housing	Compact and impact plastic injection case with plastic mirror type reflector.
Range Select	Automation.
Circuit	This stroboscope/tachometer employs an custom one-chip of microcomputer LSI circuit & crystal control time base which results in extraordinary accuracy over a wide, dynamic range.
		Calibration	Crystal time base and microprocessor circuit, don’t necessary take any external calibration process.
		Accessories Included	Operation manual……… 1 PC.

FLASH TUBE SPECIFICATIONS
Flash tube	Xenon lamp.	Flash tube replacement	It is required to change the flash tube when the instrument start to flash irregularly at speeds of 3600 RPM/FPM or more.
Flash Duration	Approximately 60 to 1,000 microseconds.
Flash color	Xenon white 6,500 K degree.
Flash energy	4 Watts-seconds (joules).
Beam Angle	80
Operating duty Cycle	For prolong life and safe operation, please adhere to the following duty cycle: Below 1,000 RPM – 30 Minutes. Above 3,600 RPM – 5 Minutes. Always allow a 10 minute cooling off period between cycles.

OPERATIONS PROCEDURES
Preparation	(a) Plug unit into a properly grounded 110V AC, 220V AC or 230V AC outlet. (b) Turn the power switch to “on” position. (c) Determine the range switch to “Low” or “High” position.
Checking Speed	When checking speed, care must be taken to insure that the strobe is flashing in unison (one to one) with the object being monitored. A Stroboscope will also stop motion at 2:1, 3:1, 4:1 et., this is normally referred to as harmonies. To be sure of unison, turn the dial until two images appear – this will double the actual speed. Then lower the flashing rate until a single and stationary image appears – this is the actual true speed.
Checking Motion	For motion analysis, simply locate the actual speed as mentioned above and then turn the dial slowly up or down. This will give a slow motion effect allowing complete inspection.